![]() 1 What are the error codes for a Raymond forklift?.To start so the fork truck can move back and forth! I'm trying to find out what the A 8 code is and the proper way to reset the computer to remove the wrench symbol and clear all codes. Socket that looked burnt pretty badly I didnt play with it but I'm thinking I'm probably going to have to cut that socket out and clean wires back and reconnect them together to get the drive motor I have a toyota Electric Fork lift That has had some serious problems as I had to get into it pretty deep to find out why when the owners guys turned on the key nothing powered up? Im not a class AĮlectric fork lift technician but I know enough about electrical that I chased down a Five pin plug that was all melted together and shorted out I removed burnt socket and replaced the burnt wiresĪnd got power back to the ignition and truck I got it so it powers the hoist and power steering but have do final drive forward or reverse I have a wrench and a Code A 8 I did see another electrical Load indicator display changes IG fuse blownĦ8-1 Lift switch abnormal Fork won't come down Connector is brokenĮrror mode Symptoms on the forklift Possible cause of failureĦ9-1 Backward tilt lock solenoid Backward tilt does not operate Connector is faultyħ1-1 Tire angle sensor abnormal Steer knob is not in position Connector is faultyħ2-1 Steering angle sensor abnormal Steer knob is not in position Connector is faultyħ3-1 Abnormal solenoid knob position Steer knob out of position Connector is faultyħ4-1 Measuring value of matching tire angle Steer knob is not in position Matching value Mast control function is partially restricted Lifting height swt is brokenĭrive control function is restricted Controller is faulty The horizontal tilt angle value does not match.Ħ7-1 Lifting height switch abnormal Partial rearwheel swing control function Faulty connector Broken connector cableĦ6-1 Abnormal matching measurement value The control mast function is partially restricted. Load indicator does not appear on the display (MFD) The controller is brokenĮrror mode Symptoms on forklift Possible causesĦ2-1 Tilt angle sensor abnormal Mast control function is partially restricted Connector is faultyĦ 3-1 Tilt lever switch abnormal Mast control function is partially restricted Connector is faultyĦ4-1 Lift lock solenoid abnormal Fork won't come down Connector is brokenĦ5-1 Tilt control solenoid abnormal Forward tilt cannot operate, but Connector is damagedīackward tilt operable. Broken connectorĦ1-2 Control mast function is partially restricted Connector cable is damagedĭrive control function is limited (MFD opt) Load sensor is faulty Broken connectorĦ1-1 Load sensor abnormal Rear wheel swing control is limited. Broken connectorĥ4-1 Swing lock solenoid abnormal Rear wheel swing control is limited. Steer knob is not in position Speed sensor is brokenĥ2-1 Yaw rate sensor abnormal Rear wheel swing control is limited. ![]() Each error code and the time at which it occurred are displayed alternately at 2Ĥ1-1 Matching connector abnormal Only the Connector display is faultyĥ1-1 Speed sensor abnormal Speed indicator keeps showing 0 km/h Connector is faultyĥ1-2 Rear wheel swing control Damaged connector cable and error code are displayed each time the knob switch is pressed and released. For how to display the main menu, refer to (1) From the main menu, display the diagnosis memory menu. Here the display method using the hour meter and tilt lever is described. Diagnosis memory display method To display the diagnosis memory display, there are a method using the hour meter and tilt lever, a method using the optional display, and a method using a When this happens, stop the vehicle immediately and check the error code.Ģ. Travelling or performing meterials handling operations, an error code is displayed and the lamps turn on as a warning. With the ignition key switch ON, if an abnormality is detected when the vehicle is stopped, ![]() The lamp lights once to allow checking for the bulb, and then turns off again if the status is normal. When the ignition key switch is turned ON, Diagnosis display method The diagnosis is displayed by means of an error code as shown in the illustration to the left, and by the lights turning on.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |